下表展示的是台站 / 对象 SP9CXD-10 在数据库中保存的最新遥测报文。如果未显示任何数据，则说明在最近 10 天内未接收到任何遥测报文。
遥测报文通常用于上报诸如中继参数、电池电压、辐射强度等各类测量值（以及其他自定义测量）。
| 时间 | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1764906320 | 43 | 76 | 21 | 4.23 | 0 |
| 1764905719 | 41 | 73 | 20 | 4.23 | 0 |
| 1764905119 | 39 | 70 | 19 | 4.23 | 0 |
| 1764904518 | 37 | 62 | 18 | 4.23 | 0 |
| 1764903918 | 35 | 59 | 17 | 4.23 | 0 |
| 1764903319 | 34 | 57 | 17 | 4.23 | 0 |
| 1764902718 | 32 | 54 | 16 | 4.23 | 0 |
| 1764902117 | 30 | 51 | 15 | 4.23 | 0 |
| 1764901517 | 28 | 48 | 14 | 4.23 | 0 |
| 1764900914 | 26 | 45 | 13 | 4.23 | 0 |
| 1764900314 | 24 | 42 | 12 | 4.23 | 0 |
| 1764899713 | 22 | 39 | 11 | 4.23 | 0 |
| 1764899113 | 20 | 36 | 10 | 4.23 | 0 |
| 1764898512 | 18 | 33 | 9 | 4.23 | 0 |
| 1764897911 | 16 | 30 | 8 | 4.23 | 0 |
| 1764897311 | 14 | 27 | 7 | 4.23 | 0 |
| 1764896711 | 12 | 24 | 6 | 4.23 | 0 |
| 1764896109 | 10 | 21 | 5 | 4.23 | 0 |
| 1764895508 | 9 | 18 | 5 | 4.23 | 0 |
| 1764894907 | 7 | 15 | 4 | 4.23 | 0 |
| 1764894307 | 5 | 11 | 3 | 4.23 | 0 |
| 1764893706 | 3 | 7 | 2 | 4.23 | 0 |
| 1764893106 | 1 | 3 | 1 | 4.23 | 0 |
| 1764892505 | 148 | 1003 | 67 | 4.23 | 0 |
| 1764891904 | 146 | 998 | 66 | 4.23 | 0 |
*使用的公式系数：
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)